# Lowpass filter for pure sine inverters

Please let us in the comment zone any suggestions that you think will improve the article!

If you like the article click the follow button  to stay in touch with us!

If in the previous posts i have designed a method to generate a control signal for obtaining a pure sine wave and an H bridge in order to use this signal in different aplications such a pure sine inverter; in this post i’ve designed a low pass filter for this inverter which is mounted on the output of the bridge at 12 volts.

I must admit that, it was a little difficult to create this filter  and i still don’t know if my design is good.  I used this filter in different tests and applications and for me it is good enough,  as you can see on  the images taken from my oscilloscope (in the end of this post). I will start with a little theory about the transfer functions and after that I will implement the design and finally, some tests.

### 1.The transfer function

Most low pass filter described on the internet are RC-low pass filter, but putting a resistor in the current way is not such a good thing. So, i have made a low pass filter from three pieces R,L and C.
The first component is the inductor and after that the capacitor in parallel with the resistor. The current will flow much easier on the inductor at low frequencies, but at higher frequencies it wil act like an high impedance, because as we know XL=L x Omega, where omega is the frequency in radians. The capacitor acts in the opposite way: at low frequency it behaves like an intrerupted circuit and at higher frequencies like a shortcircuit.
The resistor is for damping, because the internal resistance of L is negligible and some unwanted regims can appear .

The transfer function is nedeed for calculating the cuttoff frequency , the damping factor and the response of the filter.
The transfer function presented below is only for L C components in order to compare and justify the present of the resistor in circuit. The disavantage of this filter is that, near the cuttof frequency unwanted regims can appear because zeta is zero and it introduces some noise at that frequency, like in the picture below. The scales are orientative; the gain and the frequency can be bigger than 20 and 10^5 from the chart: For:

zeta=0, the system is undumped;

zeta=0.707<1, the system dumped;

zeta=1, the system is critically dumped and no peaking.

So, in order to make zeta ≠zero, i have introduced a resistor in parallel with the capacitor.
Before showing you the new transfer function, i have to say that i haven’t obtained the desired zeta because when i’ve calculated the wanted omega, the selected values for L and C gave a very small value for zeta. So, the transfer function of the circuit with the damping resistor is: Ok, as you can see in this circuit, zeta (the damping factor) is different from zero, so we can controll it.

### 2. R, L, C parameters

In practice, for low pass filter you can choose a cutoff frequency between 10 times bigger than the fundamental frequency (in our case 50 Hz for inverter) and 10 times smaller than the pwm frequency (in our case aprox. 3100Hz). I’ve tried to select a cuttof frequency around 2 kHz, so i choosed a 20 uF ceramic capacitor, a 200 uH inductor (another values i don’t have :)) ) and a 50 ohms resistor.

With these values, the cuttof frequency (in Hz) is f=2055.724 and the damping factor zeta=0.0224.

As i said, the damping factor zeta is very low comparative with 0.707. To improve this factor i could reduce the value of R but a small value across voltage means power loss or a bigger inductor. The problem with bigger inductor is that, the smallest duty cycles pwm pulses(at extreme of half duty cycle) dissapears so, between the half duty cycle of the sine wave is a period at zero volts which is unacceptable.

Ok, but you may say if zeta is very small why do you put the resistor…?

Well, if you look at the pictures below is a big difference between the circuits without and with the resistor on a frequency response chart obtain from the transfer function.

Without the resistor: With the resistor: As you can see without the resistor the gain is around 50dB and with resistor around 25dB, so, even is not a great dumping reducing the gain at half is a good thing.

### 3. Tests

Before to start the tests with the filter from R,L,C defined above, i must say that, in the image below is the oscilloscope reuslts from same filter but with a higher inductance L=15mH, and you can see how the pwm pulses with small duty cycle dissapear. This is the reason why i haven’t succed to improve the damping factor with inductance. To have an idea what means a 200uH inductor you can see below(it is made from an old pc power supply and i’ve dimensioned it with a multimeter capable to measure inductance): Next the tests with the filter will be performed with some consumers direct on the 12 voltage output and another tests with two tipes of transformers an iron core transformer and a ferite core transformer to observe the differences between this two. • filter with a 8.2 ohms 10W resistor • filter with a 8.2 ohms resistor in series with a 62mH inductor(z=omega x L=2 x pi x f x L=19.46ohms(at 50Hz)) • filter with a 12volts 16W halogen spot • filter with 12volts 5.5W LED spot in this case the sine wave is with low noise compared to other loads, and it is like the case with filter with no load.

• iron core transformer with no load(the peak voltage will be 12 volts on the low voltage side so on the high voltage side the 220 volts represent the peak value)

-on the 12 volts side -on the 220 volts side • 220V peak voltage iron core transformer and a phone charger(it accept voltages between 100-240 volts so, it should work fine) i must say that, the phone is charging with no problem.

• ferrite core transformer with no load As you can see there is no diferences between these types of transformers

• ferrite core transformer with a phone charger Also neither in this case are differences.

Final tests are with two AC motors 15W and 50W both fans. The one with the smaller power it is with a shortcircuit spire in the stator and the other one is with capacitor.

• 15W ac motor • 50W ac motor In the picture below is presented the whole pure sine inverter(sorry for aspect 🙂 ): Two video with motors:

## 3 thoughts on “Lowpass filter for pure sine inverters”

1. matt

thanks sir . .

2. Thai Lam Cao

How stable is the output voltage when load changes ?

1. admin

I don’t know if you saw the videos, but in the one with 50W ac motor is a fan with 3 speeds and when i change the speed(the click in the video) only changes appear at zero crossing between half duty cycles, the amplitude in this case is not the desired one because i’ve used a dc power supply only with 3 amps which is 36W (i don’t have other).
I try also with the fan at 15W to brake it with my hand and on the oscilloscope nothing different appear than normal functioning.
Hope that help! 🙂